Flame Jet Cutting Burner for Granite Quarry
Basic Info
Model No.: BLB65
Product Description
Model NO.: BLB65
Cutting Depth: 10m
Air Consumption: 6cbm Per Minute
Specification: as per order quantity
HS Code: 82077090
Cutting Speed: 1-2 Square Meter Per Hour
Cutting Seam Width: 80-100mm
Trademark: none
Origin: Xiamen, China
Flame jet cutting machine is a way to cut rocks with high efficiency and the character of easily operation. It is driven by the diesel oil as the fuel, air compressor as the supporter of combustion. In virtue of spraying, heatingup, and burnning, then forming high tempreture through the spear mouth, and it will eject large flame to rocks, which make the thermal energy spread on the surface of the rock and break it rapidly, then forming stone pieces which will be blown by little wind layer by layer, demolishing gradually, and forming stone trench at last, it can enhance the mining speed several times comparing to the manual in the past, and features fast speed, high efficiency, non-demolishing the former texture, it is widely used to mine the granite stone.
Operation steps
1. Please refer to below photo, connect the water-filtter device, oil tank and control valve to the compressor in rigth way.
2. Then turn on the valve on air compressor. Open the oil switch and light some diesel in the fire-pan. Warm-up the head of the burner 10-15 minutes. Use the left hand to control the oil switch, while right hand controls the air switch. Open the air switch to 1/3 position first, then trun back quickly. Again open the air switch to 1/3 position. This process can inhale the warm-up flame into the burner. Slowly open the air switch and oil switch at this time, then open the air switch to the end. The fire is ignite after this.
Try to cut the block and check the flame. Adjust the oil switch according to the smoke and cutting speed. Start working after adjustment.
3. After the work, turn off the oil switch first, then turn off the air switch.
Notice:
1. Don't aim anyone while light the burner to avoid injuries.
2. Tie the connectors of air pipe and oil pipe tightly.
3. Air humidity will affect the normal work. Try to exclude the moisture in the air if possible.
One complete set of flame cutting machine including:
Diesel hose Φ 8mm: 50meter
Diesel tank: 1pc
Burner: 2pcs
Water/air filter device: 1pc
Flaming rod: 6meter
Nozzle: 1pc
Manometer: 1pc
Lighting plate: 1pc
Pressue oil filtter: 1pc
Cutting speed | 1-2 m 2 /h |
Cutting-seam width | 80-100mm |
Air pressure | 0.6Mpa |
Cutting depth | 0-10m |
Oil tank limited pressure | 1.5Mpa |
capacity of oil tank | 850kgs |
Inner diameter of oil tube | 8mm |
Inner diameter of Air Hose | 25mm |
Air consumption | 6m 3 /min. |
Fuel consumption (oil) | 25-30kg/h |
Contact us if you need more details on Flame Burner Head. We are ready to answer your questions on packaging, logistics, certification or any other aspects about Flame Cutting Burner、Flame Jet Burner. If these products fail to match your need, please contact us and we would like to provide relevant information.
Product Categories : Rock And Concrete Splitter
Premium Related Products
Other Products
Hot Products
Pushing Air Bag for Marble Block CuttingBq90 Down The Hole (DTH) Drilling Machine for Hard RockSecoroc Cop DTH Back Hammer for Drilling & MiningMost Popular Mining DTH Hammer Breakout BenchDTH Drill Rod Pipe Drill Tube for DTH DrillingTungsten Carbide Taper Drill Chisel Bit for QuarryingShank Hex 22*108mm Taper Drill Rod with Angle 6-12 DegreeShank Hex 19X108 and 22X108 Chisel Bit Integral RodHydro Pushing Bag for Stone QuarryingLow, Middle, High Pressure DTH Hammer for DrillingHydraulic Block Push Machine for QuarrySplit-AG Splitting Expansive Mortar for Breaking StoneHot Sale Pushing Air Bag for Marble and Granite Block Cutting12 1/4" IADC537 TCI Tricone Bit for Mining and OilingHard Rock Down The Hole DTH Drill Bits/Button Bits7 Degree 36mm Button Rock Drill Jack Hammer Bits